Description
SW900 LCD Display for E-Bike Conversion Kits — 24V–72V, UART Protocol
Large LCD display showing speed, battery level, assist level (0–9), trip and total distance, motor power and error codes E0–E13. Supplied with several of our hub motor conversion kits, and also sold separately as a replacement or upgrade.
UART protocol
PAS 0–9
Speed / ODO / Watts
Errors E0–E13
ABS case, IP65
Overview
The SW900 is one of the most widely used displays for e-bike conversion kits. The large LCD stays easy to read in direct sunlight, and the ABS case with a hard acrylic screen (similar to tempered glass) is built for everyday riding in all weather.
Three buttons — Up (+), M (Mode) and Down (−) — control the assist level, the menus and every setting. No tools or phone app are needed.
Set the correct battery voltage first (P03)
Always set P03 to match your battery. The display ships set to 36V. If P03 does not match the real battery voltage, the battery level can read wrongly and error E6 (low voltage) can appear even when the battery is fully charged.
To change it: hold Up and Down together for 3–4 seconds to enter the settings menu, press M briefly to move on to P03, use Up or Down to choose the voltage that matches your battery, then hold M to save and exit. Next, set P06 to your exact wheel diameter in inches (for example 26.0, 27.5 or 29.0) so the speed reads correctly.
Technical specifications
| Operating voltage | Battery voltage up to 72V (set in P03) |
| Communication protocol | Standard UART |
| Connector | 7 wires: a 5-pin main connector plus a separate 2-wire light-control connector (brown and white) |
| USB port | 5V / 500mA |
| Protection rating | IP65 |
| Operating temperature | −20°C to +70°C |
| Case material | ABS with hard acrylic screen |
| Handlebar mount | 22.2 mm or 25.4 mm |
| Speed display | Current / maximum / average (switchable), in km/h or mph |
| Also shows | Battery level bars, assist level 0–9, trip distance, total distance (ODO, resettable), instant power in watts, error codes E0–E13 |
| Walk mode | 6 km/h, started from the button |
Wire colours — 7-wire connector
Useful for fault finding or reconnecting the display:
| Wire | Code | Function |
|---|---|---|
| Red | D+ | Power positive |
| Black | GND | Power negative (ground) |
| Blue | DS | Controller electric lock (door lock) |
| Brown | DD+ | Light control, positive (if the controller supports it) |
| Green | RX | UART receive (data from controller to display) |
| Yellow | TX | UART transmit (data from display to controller) |
| White | GND | Light control, negative (light ground) |
Note: the brown (DD+) and white (light ground) wires are only needed if your controller supports light control. If it does not, leave them unconnected and insulate the ends.
Riding modes
Reduced power and lowest consumption for the longest range. Suits flat commuting at low speeds.
The default mode. A balance of power and consumption for everyday mixed riding.
All the available power, with higher consumption. For hills, rough ground or heavy loads.
Controlled by the throttle alone, with pedal assist switched off. Set with P10 = 1.
Constant 6 km/h assistance, handy for steps or tight spaces.
Using the three buttons
A short press is under 1 second. A long press is 2–3 seconds held down.
M button — Mode / Menu
Short press: switch the data in the multi-function area (ODO → TRIP → WATT → Error). Long press: switch the screen on or off. In the menu, a short press moves to the next parameter and saves the current one; a long press saves and exits the menu.
Up button — Plus
Short press while riding: assist +1 level. Short press in the menu: increase the value. Long press: switch the speed display between current, MAX and AVG.
Down button — Minus
Short press while riding: assist −1 level. Short press in the menu: decrease the value. Long press with the bike stopped: walk mode at 6 km/h (release to exit). Long press: switch the light on or off.
Entering the settings menu
Hold Up and Down together for 3–4 seconds to open parameters P01–P16. If you press no button for 10 seconds inside the menu, changed values are saved automatically and the display exits the menu.
Error codes E0–E13
The error code appears in the multi-function area of the screen. E0 means normal operation.
| Code | Meaning | What to do |
|---|---|---|
| E0 | Normal, no error | — |
| E1 | Saving in progress | Information only |
| E2 | Brakes applied, motor cut off | Release the brake levers fully |
| E3 | PAS problem (not implemented in current firmware) | Information only |
| E4 | 6 km/h walk mode active | Information only |
| E5 | Real-time cruise active | Information only |
| E6 | Low battery voltage (undervoltage) | Charge the battery and check that the voltage set in P03 matches it |
| E7 | Motor problem | Check the motor-to-controller connections (3 phase plugs and Hall sensor plug) |
| E8 | Throttle problem | Check the throttle connections; look for a short circuit or mechanical fault |
| E9 | Controller problem | Check the controller power supply and main connections |
| E10 | Communication receive error | Check the green wire (RX) between display and controller |
| E11 | Communication transmit error | Check the yellow wire (TX) between display and controller |
| E12 | Battery BMS communication error | Check the battery connection and the BMS |
| E13 | Headlight problem | Check the headlight connections and the white wire (light ground) |
Programmable parameters P01–P16
Enter the menu by holding Up and Down together for 3–4 seconds. Move on with a short press of M, change values with Up or Down, and hold M to save and exit.
| Param | Function | Values / notes |
|---|---|---|
| P01 | Screen backlight brightness | 1 = darkest, 3 = brightest |
| P02 | Distance unit | 0 = kilometres, 1 = miles |
| P03 | System voltage | Any battery voltage up to 72V. Default 36V. Set it to match your battery. |
| P04 | Standby time (auto sleep) | 0 = no sleep, 1–60 = minutes until automatic switch-off |
| P05 | Number of assist levels | 0 = 3 levels (2V / 3V / 4V), 1 = 5 levels (2V / 2.5V / 3V / 3.5V / 4V) |
| P06 | Wheel diameter | In inches, 0.1 precision, for example 26.0 / 27.5 / 29.0 |
| P07 | Number of speed sensor magnets | 1–100. Check the speed sensor that came with your kit |
| P08 | Speed limit | 0–50 km/h, where 50 = no limit. Applies to pedal assist; the throttle may be unaffected without communication |
| P09 | Zero start / non-zero start | 0 = zero start (pedal first, then the motor starts), 1 = non-zero start (motor starts immediately) |
| P10 | Drive mode | 0 = pedal assist only, 1 = throttle only, 2 = pedal assist + throttle (throttle disabled at zero start) |
| P11 | Pedal assist sensitivity | 1–24. Lower values react faster to pedalling |
| P12 | Assist start strength | 0–5. How hard the motor starts on the first assist signal |
| P13 | Assist sensor magnet type | 5, 8 or 12 magnets. Check the PAS sensor in your kit |
| P14 | Controller current limit | 1–20A, default 12A. Raise it step by step if you need more torque on take-off |
| P15 | Not used | Reserved for future firmware. Do not change. |
| P16 | Reset total distance (ODO) | Hold the M button for 5 seconds to reset the total distance to zero |
Compatibility and use
Replacement display
A like-for-like replacement for the SW900 supplied with our hub motor kits: same UART protocol, same connection, same fitting.
Upgrade
Step up from a basic display to a full LCD with speed, ODO, watts, error codes and 16 programmable parameters.
DIY UART builds
A key part of any DIY conversion that uses a UART controller.
Protocol check before ordering: the SW900 works only with UART controllers. It is not compatible with KT controllers (their own protocol) or with Bafang systems (a different UART). If you are replacing a controller as well, make sure the new one uses the same protocol. The controller’s product page lists the displays it supports.
See our hub motor conversion kits and e-bike controllers.
Frequently asked questions
What should I set first after installing the display?
Hold Up and Down together for 3–4 seconds to open the menu and set P03 to match your battery voltage. Then set P06 to the exact wheel diameter in inches so the speed is correct. The display comes set to 36V and 26 inch.
Why does E6 appear when my battery is charged?
E6 (low voltage) usually appears when the voltage set in P03 does not match the real battery voltage. For example, with a 48V battery and P03 left on 36V, the display treats the battery as flat. Open the menu and set P03 to your battery voltage.
How do I switch between km/h and mph?
Open the menu and go to P02. Set 0 for kilometres or 1 for miles. Speed and distance convert automatically. The P08 speed limit stays stored in km/h in the display’s memory, so check it again after changing units.
How do I use walk mode (6 km/h)?
With the bike completely stopped, hold the Down (−) button for 2–3 seconds. The motor runs at 6 km/h and E4 shows on screen while walk mode is active. Release the button to exit.
Is the SW900 compatible with my controller?
It works with controllers that use the standard UART protocol. KT and Bafang controllers use different protocols that are not compatible. Check the protocol before ordering, or message us on WhatsApp if you are not sure.
Package includes
1 × SW900 LCD display

Peter Mayo –
Working great! My old one broke and this was shipped really fast!